Tutorial: three-hinged frame
Model a portal frame with a hinge at mid-span, read its reactions and diagrams, and check every number by hand, down to the deflection of the hinge.
- Time: about 15 minutes.
- You need: EduBeam open in a second tab, on a computer with a mouse and keyboard. The Quick start or the inclined beam tutorial first, if you have not used EduBeam before.
- Background: equilibrium of a frame and free-body diagrams. The optional deflection check uses the unit load method (virtual work).
- Units: SI. The units chip at the bottom right of the viewer should read
m m² kN kNm MPa. If it shows feet and kips, click it and set Unit system to SI (metric).
You will learn to
- draw a frame as one polyline with the mouse,
- put a hinge inside a member with the End hinges boxes,
- find the horizontal thrust from the condition at the hinge, and read the sign of in members drawn in different directions.
The problem
- Two 4 m columns, pinned at their bases, nodes 1 and 5, 8 m apart.
- A horizontal beam from node 2 to node 4 on top, with a hinge at mid-span, node 3.
- A uniform load kN/m on the whole beam.
- Steel, GPa, and m⁴ (an IPE 300) for every member.
| Node | x (m) | z (m) | |
|---|---|---|---|
| 1 | 0 | 0 | pin |
| 2 | 0 | −4 | corner |
| 3 | 4 | −4 | hinge in the beam |
| 4 | 8 | −4 | corner |
| 5 | 8 | 0 | pin |
The z axis points down, so the tops of the columns are at .
Is it determinate? Two pins give four reactions. Three equations of equilibrium and at the hinge make four equations: yes.
Model it
Material and section
- Click Clear mesh in the app bar, tick Delete materials and Delete cross sections, and click Confirm. Nodes and elements are numbered from 1 again.
- Materials tab → Material library → + on the Steel (S235) row, then Cancel to close the library.
- Cross sections tab → Add cross section. Type
8.356e-5in Iy, keep Area, Height and Shear coefficient at1, and click Add cross section.
An area of 1 m² keeps the members from shortening or shearing noticeably, as the hand calculation of the deflection assumes. The internal forces of a determinate frame do not depend on , or at all.
Draw the frame
- Elements tab → the second Add element button, the one with the cursor icon.
- Click at (0, 0), (0, −4), (4, −4), (8, −4) and (8, 0). Each click adds the next node and connects it to the previous one; the clicks snap to the grid.
- Press Esc to stop drawing, then F to fit the view.
You now have nodes 1 to 5 and elements 1 to 4, numbered in the order you drew them, as in the figures here. Compare the Nodes table with the table above and type over any coordinate that missed.
Supports and the hinge
- Click node 1 → Node supports → the Pin symbol. Do the same for node 5.
- In the Elements table, find element 2, from node 2 to node 3, and tick the second of its End hinges boxes: the hinge at its end, at node 3.


One hinge is enough. Element 3 is then the only member rigidly attached to node 3, so no moment can pass into it there. Ticking the start of element 3 as well changes nothing.
Load
- Loads tab → Add element load.
- Load type Uniformly distributed load, Element
2,fz = 10. Click Add element load. - Repeat for element 3.
fz is positive downward. The beam is horizontal, so the LCS box makes no difference here.
Results
In the display options at the top right of the viewer (the cog shows and hides them), Deformed shape, My (x) and Reactions are on from the start. Tick N (x) and Vz (x) for the rest, or untick some to see one diagram at a time. EduBeam labels them in kN and kNm with two decimals.
- Each base reads
40.00upward and20.00inward. - The bending moment reads
-80.00at both corners and has no label at the hinge, where it is zero. EduBeam draws it on the tension side, here outside the frame. - The normal force is negative everywhere:
-40.00in the columns,-20.00in the beam. All four members are in compression. - Results tab → Nodal results: the hinge, node 3, moves down by =
4.2554 · 10⁻² m, that is 42.55 mm, the value at the hinge in the view of the figure above.
Check by hand
Vertical reactions. By symmetry each base takes half of the 80 kN:
Horizontal reactions. Cut the frame at the hinge and take moments about node 3 for the left half, where the moment is zero:
Both bases push inward by 20 kN. Without that thrust, from pins that cannot slide apart, the frame could not stand: the columns would splay and the hinge would drop.
| Quantity | Formula | By hand | EduBeam |
|---|---|---|---|
| Vertical reactions | 40 kN | 40.00 | |
| Horizontal reactions | from | 20 kN | 20.00 |
| Moments at the corners, nodes 2 and 4 | 80 kNm, outside | −80.00 | |
| Moment at the hinge, node 3 | 0 | no label | |
| in the columns | −40 kN | −40.00 | |
| in the beam | −20 kN | −20.00 | |
| in the columns | ±20 kN | −20.00, 20.00 | |
| in the beam at nodes 2, 3, 4 | 40, 0, −40 kN | 40.00, no label, −40.00 |
The two columns carry the same shear with opposite signs, −20 kN in element 1 and +20 kN in element 4, because each element's local axes follow the direction it was drawn in: element 1 upward, element 4 downward. Swap the nodes of one column and its sign flips. The sign conventions explain why.
In the beam, kNm, with measured from node 2. It is zero at the hinge and never positive: the whole beam hogs. The shear is zero exactly at the hinge, so that is where the moment has its extreme.
The deflection of the hinge, by virtual work
Put a unit load downward at node 3. It gives reactions and a moment that grows from 0 at a base to 2 at a corner and falls back to 0 at the hinge, with tension outside, like the real moment . Integrate over the four members:
With kNm²:
That is the 42.55 mm EduBeam reports as 4.2554 · 10⁻² m. The 4 in the last digit is the tiny shortening and shearing that an area of 1 m² still allows, which the hand calculation leaves out. With the real area of an IPE 300, cm², and its web as the shear area (a shear coefficient of 0.40), the members shorten and shear more, and the hinge drops 43.7 mm, about 3 % more.
Experiment
Change one thing at a time, predict the result, then look. Ctrl+Z takes each change back.
Untick the hinge. The frame becomes once statically indeterminate. The thrust halves to 10 kN, the corner moments drop to −40 kNm, and the beam sags by 40 kNm at mid-span. Node 3 now moves down only 12.16 mm instead of 42.55 mm. The sections matter now too: give the beam a stiffer section than the columns and the corner moments grow.
Fix the bases. Give nodes 1 and 5 the Fixed symbol. The thrust rises to 30 kN and moments of 40 kNm appear at the bases (EduBeam shows 39.99, because the columns shorten very slightly), yet the corner moments stay at 80 kNm. By symmetry the shear at the hinge is zero, so each half of the beam still works as a 4 m cantilever from its corner: kNm.
Push sideways. Back on pins, add a nodal load Fx = 10 kN at node 2. The reactions lose their symmetry: 35 kN and 45 kN up, 15 kN and 25 kN horizontal. Check them with the same three equations and ; the load at node 2 has no lever arm about node 3. The left corner drops to −60 kNm, and the left half of the beam now sags slightly, by 1.25 kNm at 0.5 m from the hinge.
Add a second hinge. Tick the start hinge of element 2 as well, at node 2. Two hinges in the beam on two pinned columns make a mechanism. EduBeam shows no results, reports The hinges at nodes 2, 3 let the structure move., and animates the motion.
Next steps
Practise: three-hinged frames
The same frame under new loads, a horizontal push among them, with your answers checked at once. Start with H2048; for more, keep only Three-hinged frame selected and press New problem.
Next: plane truss
Nine hinged bars: the method of joints, the method of sections, a zero-force member and a deflection by virtual work.